Skip to main content

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [List Home]
Re: [sumo-dev] Issue with Sumo Simulation - Edgedata Output for Specified Time Range

I did it! I am truly thankful.

Yuji

2023年6月12日(月) 21:32 Jakob Erdmann <namdre.sumo@xxxxxxxxx>:
<additional>
   <edgeData id="example" file="edgedata_test.xml" begin="23400" end="40000"/>
</additional>

Am Mo., 12. Juni 2023 um 13:23 Uhr schrieb 渡邊勇志 <yuyujiji0201@xxxxxxxxx>:
Thank you for your response. I tried loading the additional XML into my .sumocfg file, but the "begin" attribute of the Edge data became 0. The contents of the additional xml are written as follows:

"Additional.xml"
<additional>
<time>
<begin value="23400"/>
<end value="40000"/>
</time>
</additional>

I apologize if this is a basic question, but how can I specify a time range in the output data using the contents of the additional xml? 
Could you please provide guidance on this matter?

Sincerely,
Yuji

2023年6月12日(月) 16:24 Jakob Erdmann <namdre.sumo@xxxxxxxxx>:
Hello,
the option **--edgedata-output** does not support a custom time range. To set a custom time range you need to define the edgeData output with 'begin' and 'end' attributes in an additional xml file and load this file in your .sumocfg.

Am Mo., 12. Juni 2023 um 08:59 Uhr schrieb 渡邊勇志 <yuyujiji0201@xxxxxxxxx>:
Hello,

I hope this email finds you well. I am writing to seek assistance regarding an issue I encountered while using the Sumo simulation tool.

I successfully generated an edge-based state dump output by entering the command "--edgedata-output <FILE>" in the command line. The output was produced correctly. However, when I attempted to output data for a specific time range by specifying the time using the additional attributes -b (--begin) and -e (--end), the results were not as expected. I noticed that setting the begin parameter to 0 resulted in the correct output, but I require the output for the specified time range.

I would greatly appreciate it if you could provide guidance on how to correctly output the data when the begin parameter is set to a value other than 0, ensuring that it corresponds to the desired time range.

<!-- generated on 2023-06-12 15:33:24 by Eclipse SUMO sumo Version 1.16.0 <configuration xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://sumo.dlr.de/xsd/sumoConfiguration.xsd"> <input> <net-file value="manhattan.net.xml"/> <route-files value="sumotest.trips.xml"/> </input> <output> <edgedata-output value="edge_test.xml"/> </output> <time> <begin value="34000"/> </time> <report> <no-step-log value="true"/> </report> </configuration> -->
<meandata xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://sumo.dlr.de/xsd/meandata_file.xsd"> </meandata>

Thank you for your attention to this matter. I look forward to your prompt response.

Yours sincerely,

Yuji



_______________________________________________
sumo-dev mailing list
sumo-dev@xxxxxxxxxxx
To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev
_______________________________________________
sumo-dev mailing list
sumo-dev@xxxxxxxxxxx
To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev
_______________________________________________
sumo-dev mailing list
sumo-dev@xxxxxxxxxxx
To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev
_______________________________________________
sumo-dev mailing list
sumo-dev@xxxxxxxxxxx
To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev

Back to the top