[
Date Prev][
Date Next][
Thread Prev][
Thread Next][
Date Index][
Thread Index]
[
List Home]
|
Re: [p2-dev] [equinox-dev] Writing something into the config.ini file
|
Hi Andrew,
Is there a document that describes these states?
Also, I tried the configure phase, but no luck. I am not sure what I am
doing wrong. I have attached my project, would you have time to have a
look?
Thanks in advance,
Dom
There is probably an ordering
issue. The root files will be artifacts
associated with a second IU "feature_root" that is required by your feature's
IU. It is likely that the feature is getting installed first and the root
file IU will be done a bit later, so when the feature's install actions run, the
zip has not been extracted yet. The
zip will be extracted during the install phase for the root IU, the configure
phase happens later, so things should work better if you move the unzip action
to the configure phase. -Andrew
| From:
| Domenico Alessi
<domenico.alessi@xxxxxxxxxxxx>
|
| To:
| Equinox development mailing list
<equinox-dev@xxxxxxxxxxx>
|
| Cc:
| P2 developer discussions
<p2-dev@xxxxxxxxxxx>
|
| Date:
| 05/12/2011 12:38 PM
|
| Subject:
| Re: [p2-dev] [equinox-dev] Writing
something into the config.ini file
|
| Sent by:
| p2-dev-bounces@xxxxxxxxxxx |
Hi Guys, So trying some other
nifty stuff out. I have placed a zip file into the feature and I have this
as my p2.inf instructions.configure =
\
org.eclipse.equinox.p2.touchpoint.eclipse.setProgramProperty(propName:testValue1,propValue:testValue2);\
instructions.install =
\
org.eclipse.equinox.p2.touchpoint.natives.unzip(source:${installFolder}/test_temp/test.zip,target:${installFolder}/);\
Now, the
zip files is there after installation as I set it to be there using
root.folder.test_temp=file:test.zip
in my feature build.properties
I see the
following in my context.xml - <touchpointData size="1">
-
<instructions size="2">
<instruction
key="install">org.eclipse.equinox.p2.touchpoint.natives.unzip(source:${installFolder}/test_temp/test.zip,target:${installFolder}/);</instruction>
<instruction
key="configure">org.eclipse.equinox.p2.touchpoint.eclipse.setProgramProperty(propName:testValue1,propValue:testValue2);</instruction>
</instructions>
</touchpointData>
But, I don't see the zip file being
extracted. I have included org.eclipse.equinox.p2.touchpoint.natives in my
feature.xml as a dependency. Any thoughts? Thanks,
Dom
From: equinox-dev-bounces@xxxxxxxxxxx [mailto:equinox-dev-bounces@xxxxxxxxxxx] On Behalf Of Pascal Rapicault
Sent: May-11-11 3:22
PM
To: Equinox development mailing list
Cc: P2 developer
discussions
Subject: Re: [equinox-dev] Writing something into the
config.ini file
If you want to
make your example on the ML, I'm sure others would find it handy.
On 2011-05-11, at 3:21 PM, Domenico Alessi
wrote: Arg! Nevermind,
caching effect. Worked like a charm. Thanks.
Dom
From: equinox-dev-bounces@xxxxxxxxxxx [mailto:equinox-dev-bounces@xxxxxxxxxxx] On Behalf Of Domenico Alessi
Sent:
May-11-11 3:12 PM
To: Equinox development mailing list
Cc:
P2 developer discussions
Subject: Re: [equinox-dev] Writing something
into the config.ini file
Thanks Pascal. Ok, so before I put the plugin below into the
dependencies, I saw the actions in the content.jar. Now that I have put in
the include I no longer see the actions in my content.jar file. So nothing
gets placed into my config.ini, but install passes. Thanks,
Dom
From: equinox-dev-bounces@xxxxxxxxxxx [mailto:equinox-dev-bounces@xxxxxxxxxxx] On Behalf Of Pascal Rapicault
Sent:
May-11-11 2:40 PM
To: Equinox development mailing list
Cc:
P2 developer discussions
Subject: Re: [equinox-dev] Writing something
into the config.ini file
Make
sure that the org.eclipse.equinox.p2.touchpoint.eclipse is in available.
On 2011-05-11, at 2:33 PM, Domenico Alessi
wrote: Hi Pascal,
I get the following error at install
time:
An error occurred while configuring the
installed items
session context was:(profile=""
phase=org.eclipse.equinox.internal.p2.engine.phases.Configure, operand=null
--> [R]com.test.p2.feature.feature.group 1.0.0.201105111415,
action="">
No action found for:
setProgramProperty.
No action found for:
setProgramProperty.
My p2.inf looks like this:
instructions.configure=\
setProgramProperty(propName:testValue1,propValue:testValue2);\
Thanks in advance,
Dom
From: equinox-dev-bounces@xxxxxxxxxxx [mailto:equinox-dev-bounces@xxxxxxxxxxx] On Behalf Of Pascal Rapicault
Sent:
May-11-11 1:36 PM
To: Equinox development mailing list; P2 developer
discussions
Subject: Re: [equinox-dev] Writing something into the
config.ini file
This can be done
using a touchpoint action (Provisioning Actions and Touchpoints)
In this particular case: setProgramProperty,
for example setProgramProperty(propName:equinox.use.ds, propValue:true);
To get this added to your metadata you need to store that
into a p2.inf file (Customizing metadata)
On 2011-05-11, at 1:30 PM, Domenico Alessi wrote:
Hi All,
I a have quick question. I have a feature/plugin
that I wish to install but I also want at installation time to put in a
key/value pair into the config.ini. I see that install Handlers are
discouraged. How can I accomplish
this?
BR,
Dom
_______________________________________________
equinox-dev
mailing list
equinox-dev@xxxxxxxxxxx
https://dev.eclipse.org/mailman/listinfo/equinox-dev
_______________________________________________
equinox-dev mailing
list
equinox-dev@xxxxxxxxxxx
https://dev.eclipse.org/mailman/listinfo/equinox-dev
_______________________________________________
equinox-dev mailing
list
equinox-dev@xxxxxxxxxxx
https://dev.eclipse.org/mailman/listinfo/equinox-dev
_______________________________________________
p2-dev
mailing list
p2-dev@xxxxxxxxxxx
https://dev.eclipse.org/mailman/listinfo/p2-dev
Attachment:
testp2.zip
Description: testp2.zip
