| Re: [sumo-user] R: R: TraCI creation of new vehicle and route |
I changed “newCar” into “reroutingType” in order to do exactly as in the documentation, I already checked that correspondence, the line I use is:
traci.vehicle.add("car", "route1", typeID="reroutingType")
The error SUMO gives me is:
Error: Answered with error to command 0xc4: Invalid type 'reroutingType' for vehicle 'car'
Error: tcpip::Socket::recvAndCheck @ recv: Socket reset by peer
Quitting (on error).
Da: sumo-user-bounces@xxxxxxxxxxx <sumo-user-bounces@xxxxxxxxxxx
> Per conto di Jakob Erdmann
Inviato: 03 July 2018 12:12
A: Sumo project User discussions <sumo-user@xxxxxxxxxxx>
Oggetto: Re: [sumo-user] R: TraCI creation of new vehicle and route
In your call to addVehicle you use the type id 'newCar'
traci.vehicle.add("car", "route1", typeID="newCar")
but you should use "reroutingType" instead.
As it is now, routing is not attempted and the error message only indicates that the edges are not directly connected.
2018-07-03 12:06 GMT+02:00 Stefano Niero <stefano.niero@xxxxxxxxxx>:
Thank you very much. The route insertion was my mistake.
For what concerns the trip, I did read the documentation and I did equip the vehicle with a rerouting device: here is the additional file that describes the vehicle
<additional>
<vType id="reroutingType" type="passenger" length="4.5" accel="3.5" decel="2.2" maxSpeed="8.0" color="1,1,0" sigma="0.5" guiShape="passenger/hatchback"
> <param key="has.rerouting.device" value="true"/>
</vType>
</additional>
Still, the error I get if I give two non consecutive edges is:
File "C:\Program Files (x86)\DLR\Sumo\tools\traci\
connection.py", line 104, in _sendExact raise TraCIException(prefix[1], _RESULTS[prefix[2]], err)
traci.exceptions.
TraCIException: Vehicle 'car' has no valid route. No connection between edge 'gneE2' and edge '-gneE9'.
Which is not true, as a matter of fact in the same simulation there is a flow of vehicles specifies in the .rou.xml file that goes through the same trip and it works for them. Am I missing anything?
Da: sumo-user-bounces@xxxxxxxxxxx <sumo-user-bounces@xxxxxxxxxxx
> Per conto di Jakob Erdmann
Inviato: 02 July 2018 20:59
A: Sumo project User discussions <sumo-user@xxxxxxxxxxx>
Oggetto: Re: [sumo-user] TraCI creation of new vehicle and route
Hello,
1) adding a route only succeeds if the name is not already used by another route. Therefore, adding the same route again and again in a loop cannot work. The resulting error is not fatal, however. You can catch the TraCIException and continue with your script.
2) adding a trip (a route with two non-consecutive edges) only works if the vehicle is equipped with a rerouting device. This is even explained in the documentation you linked: http://sumo.dlr.de/wiki/TraCI/
Interfacing_TraCI_from_Python# Add_trips_.28incomplete_ routes.29_dynamically If no route is found between the two edges (because they are in disconnected parts of the network) you will get an exception but you can catch that as well.
regards,
Jakob
2018-07-02 19:18 GMT+02:00 Stefano Niero <stefano.niero@xxxxxxxxxx>:
Dear SUMO Community,
I tried generate a new trip and a new vehicle using the example written in the following page:
http://sumo.dlr.de/wiki/TraCI/
Interfacing_TraCI_from_Python At the beginning, to understand how it works I decided to keep things simple and used a minimal map (attached).
The line of codes I wrote are:
def run():
step = 0
while step < 1000:
#traci.simulationStep()
traci.route.add("route1", ["gneE2", "gneE5"])
traci.vehicle.add("car", "route1", typeID="newCar")
step +=1
traci.close()
sys.stdout.flush()
where the two edges are contiguous because if I select two edges that are far one from the other it tells me that no connection is available (why?). Starting the program it opens the GUI but playing the simulation it stops immediately saying:
------------------------------
------------------------------ ---------------------------- Loading configuration... done.
***Starting server on port 56264 ***
Loading net-file from 'bus.net.xml'... done (2ms).
Loading additional-files from 'bus.add.xml'... done (0ms).
Loading done.
Simulation started with time: 0.00
Error: Answered with error to command 0xc6: Could not add route.
Error: tcpip::Socket::recvAndCheck @ recv: Socket reset by peer
Quitting (on error).
-------------------------
On SUMO-GUI, while PyCharm log gives me:
Loading configuration... done.
Traceback (most recent call last):
File "C:/Stefano/For school/Tesi/TraCI/Simulation/
runner.py", line 100, in <module> run()
File "C:/Stefano/For school/Tesi/TraCI/Simulation/
runner.py", line 67, in run traci.route.add("route1", ["gneE2", "gneE5"])
File "C:\Program Files (x86)\DLR\Sumo\tools\traci\_
route.py", line 46, in add self._connection._sendExact()
File "C:\Program Files (x86)\DLR\Sumo\tools\traci\
connection.py", line 104, in _sendExact raise TraCIException(prefix[1], _RESULTS[prefix[2]], err)
traci.exceptions.
TraCIException: Could not add route.
Process finished with exit code 1
Can you tell me what I did wrong?
Thank you very much
Stefano Niero
_______________________________________________
sumo-user mailing list
sumo-user@xxxxxxxxxxx
To change your delivery options, retrieve your password, or unsubscribe from this list, visit
https://dev.eclipse.org/mailman/listinfo/sumo-user
_______________________________________________
sumo-user mailing list
sumo-user@xxxxxxxxxxx
To change your delivery options, retrieve your password, or unsubscribe from this list, visit
https://dev.eclipse.org/mailman/listinfo/sumo-user
_______________________________________________
sumo-user mailing list
sumo-user@xxxxxxxxxxx
To change your delivery options, retrieve your password, or unsubscribe from this list, visit
https://dev.eclipse.org/mailman/listinfo/sumo-user