Skip to main content


Eclipse Community Forums
Forum Search:

Search      Help    Register    Login    Home
Home » Archived » BIRT » Table rows height problem
Table rows height problem [message #1044943] Fri, 19 April 2013 14:37 Go to next message
Mimmo Rossi is currently offline Mimmo RossiFriend
Messages: 146
Registered: February 2013
Senior Member
Hi All,
there is the possibility to lock the height of a table's row to avoid that this stretching in the presence of a text too big?
I have setted the height in inches but when i export in pdf (or ppt) this expands based on text...
Thanks in advance

Report message to a moderator

Re: Table rows height problem [message #1045068 is a reply to message #1044943] Fri, 19 April 2013 18:20 Go to previous messageGo to next message
Michael Williams is currently offline Michael WilliamsFriend
Messages: 1925
Registered: July 2009
Senior Member
Are you using a fixed layout? If so, can you create a sample showing your issue that I can run? Thanks.

Michael

Developer Evangelist, Silanis

Report message to a moderator

Re: Table rows height problem [message #1045762 is a reply to message #1045068] Sat, 20 April 2013 20:54 Go to previous messageGo to next message
Mimmo Rossi is currently offline Mimmo RossiFriend
Messages: 146
Registered: February 2013
Senior Member
Hi Michael,
I do not know how to use the fixed layout, but I have attached 2 example with 2 different layouts that have the same problem even if in different ways:
1) report_A: pdf there are no bottom borders, ppt writes over
2) report_B: row spread out
Considering that the layout of these reports have already been approved, there is a way (an attribute) to set the maximum height and not allow the lines to spread and do not allow to write over?
Thanks in advance

Report message to a moderator

Re: Table rows height problem [message #1048605 is a reply to message #1045762] Wed, 24 April 2013 18:12 Go to previous messageGo to next message
Michael Williams is currently offline Michael WilliamsFriend
Messages: 1925
Registered: July 2009
Senior Member
In report B, if you set the report to fixed layout vs the auto layout it's currently in, the text seems to be cut off correctly.

Setting heights for the containing grids in report A allows the border to be shown. I cannot test for ppt because I have PowerPoint 2010.

Michael

Developer Evangelist, Silanis

Report message to a moderator

Re: Table rows height problem [message #1053720 is a reply to message #1048605] Tue, 07 May 2013 11:36 Go to previous messageGo to next message
Mimmo Rossi is currently offline Mimmo RossiFriend
Messages: 146
Registered: February 2013
Senior Member
Hi Michael,
how can i set a fixed layout?
I change a LayoutPreference in advanced section of a report, but doesn't work.

[Updated on: Tue, 07 May 2013 11:38]

Report message to a moderator

Re: Table rows height problem [message #1057734 is a reply to message #1053720] Wed, 08 May 2013 13:50 Go to previous message
Michael Williams is currently offline Michael WilliamsFriend
Messages: 1925
Registered: July 2009
Senior Member
A fixed layout can be set in the general section of the property editor. If you click on the report in a blank spot or select the report design in the outline view, then go to the property editor's general section and scroll to the bottom, you should see the option.

Michael

Developer Evangelist, Silanis

Report message to a moderator

Previous Topic:any solution for limit runaway report queries ?
Next Topic:Creating a Stacked Bar chart using a script
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Mon Dec 09 08:35:42 GMT 2024

Powered by FUDForum. Page generated in 0.04135 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.2.
Copyright ©2001-2010 FUDforum Bulletin Board Software

Back to the top

Sign up to our Newsletter

A fresh new issue delivered monthly