Home » Modeling » EMF "Technology" (Ecore Tools, EMFatic, etc) » RAP-EMF integration trouble(Problems installing EMF 2.6 in particular)
| |
Re: RAP-EMF integration trouble [message #530433 is a reply to message #530412] |
Thu, 29 April 2010 15:46 |
Ed Merks Messages: 33218 Registered: July 2009 |
Senior Member |
|
|
Aditya,
You should use the EMF newsgroup/forum.
More comments below.
Aditya Gupta wrote:
> Hi,
>
> I dont know if this is the right place to post questions about RAP,
> but since i couldnt find any other suitable link i posted it here.
>
> I went through eclipse wiki article for RAP- EMF integration, but it
> was a little confusing. First it said that i need EMF 2.6 and RAP
> Tooling 1.3 to do the integration, but just a few line below it said
> that the plugins shouldn't be installed in the IDE as it could break it.
Yes, they need to be in the target platform against which you develop
your plugins, not installed in the IDE.
>
> So I tried putting the EMF 2.6 files in the RAPTarget folder that i
> had created earlier to configure a Target Platform for running RAP
> applications. It didn't work.
Only the RAP plugins would go there.
>
> Can any one please guide me how to use RAP esp. RAP-EMF integration.
> It looks wonderful as a concept, but I am struggling to leverage it.
Hopefully Kenn can provide a few more details.
>
> Regards,
> Aditya
Ed Merks
Professional Support: https://www.macromodeling.com/
|
|
|
Re: RAP-EMF integration trouble [message #530434 is a reply to message #530433] |
Thu, 29 April 2010 15:50 |
Kenn Hussey Messages: 1620 Registered: July 2009 |
Senior Member |
|
|
All,
Please see the detailed instructions in the New and Noteworthy page at
http://wiki.eclipse.org/EMF/New_and_Noteworthy/Helios#Suppor t_for_Rich_Ajax_Platform_.28RAP.29
Kenn
Ed Merks wrote:
> Aditya,
>
> You should use the EMF newsgroup/forum.
>
> More comments below.
>
>
> Aditya Gupta wrote:
>> Hi,
>>
>> I dont know if this is the right place to post questions about RAP,
>> but since i couldnt find any other suitable link i posted it here.
>>
>> I went through eclipse wiki article for RAP- EMF integration, but it
>> was a little confusing. First it said that i need EMF 2.6 and RAP
>> Tooling 1.3 to do the integration, but just a few line below it said
>> that the plugins shouldn't be installed in the IDE as it could break it.
> Yes, they need to be in the target platform against which you develop
> your plugins, not installed in the IDE.
>>
>> So I tried putting the EMF 2.6 files in the RAPTarget folder that i
>> had created earlier to configure a Target Platform for running RAP
>> applications. It didn't work.
> Only the RAP plugins would go there.
>>
>> Can any one please guide me how to use RAP esp. RAP-EMF integration.
>> It looks wonderful as a concept, but I am struggling to leverage it.
> Hopefully Kenn can provide a few more details.
>>
>> Regards,
>> Aditya
|
|
| |
Re: RAP-EMF integration trouble [message #530617 is a reply to message #530509] |
Fri, 30 April 2010 10:25 |
Ed Merks Messages: 33218 Registered: July 2009 |
Senior Member |
|
|
Aditya,
You do need to install EMF 2.6 in Eclipse 3.6 to get the IDE portions of
this support working.
Aditya Gupta wrote:
> Hi,
>
> I tried both approaches given by Jonas as well as Kenn, but I am not
> getting the option Rich Ajax Platform in the genmodel.
>
> Is there any EMF Technology plugin that i have installed that is not
> letting this happen?
>
> I am using Eclipse 3.5.1 and the compliance level of my genmodel is 6.0
>
> Regards,
> Aditya
Ed Merks
Professional Support: https://www.macromodeling.com/
|
|
|
Re: RAP-EMF integration trouble [message #622526 is a reply to message #530433] |
Thu, 29 April 2010 15:50 |
Kenn Hussey Messages: 1620 Registered: July 2009 |
Senior Member |
|
|
All,
Please see the detailed instructions in the New and Noteworthy page at
http://wiki.eclipse.org/EMF/New_and_Noteworthy/Helios#Suppor t_for_Rich_Ajax_Platform_.28RAP.29
Kenn
Ed Merks wrote:
> Aditya,
>
> You should use the EMF newsgroup/forum.
>
> More comments below.
>
>
> Aditya Gupta wrote:
>> Hi,
>>
>> I dont know if this is the right place to post questions about RAP,
>> but since i couldnt find any other suitable link i posted it here.
>>
>> I went through eclipse wiki article for RAP- EMF integration, but it
>> was a little confusing. First it said that i need EMF 2.6 and RAP
>> Tooling 1.3 to do the integration, but just a few line below it said
>> that the plugins shouldn't be installed in the IDE as it could break it.
> Yes, they need to be in the target platform against which you develop
> your plugins, not installed in the IDE.
>>
>> So I tried putting the EMF 2.6 files in the RAPTarget folder that i
>> had created earlier to configure a Target Platform for running RAP
>> applications. It didn't work.
> Only the RAP plugins would go there.
>>
>> Can any one please guide me how to use RAP esp. RAP-EMF integration.
>> It looks wonderful as a concept, but I am struggling to leverage it.
> Hopefully Kenn can provide a few more details.
>>
>> Regards,
>> Aditya
|
|
| |
Re: RAP-EMF integration trouble [message #622532 is a reply to message #622528] |
Fri, 30 April 2010 10:25 |
Ed Merks Messages: 33218 Registered: July 2009 |
Senior Member |
|
|
Aditya,
You do need to install EMF 2.6 in Eclipse 3.6 to get the IDE portions of
this support working.
Aditya Gupta wrote:
> Hi,
>
> I tried both approaches given by Jonas as well as Kenn, but I am not
> getting the option Rich Ajax Platform in the genmodel.
>
> Is there any EMF Technology plugin that i have installed that is not
> letting this happen?
>
> I am using Eclipse 3.5.1 and the compliance level of my genmodel is 6.0
>
> Regards,
> Aditya
Ed Merks
Professional Support: https://www.macromodeling.com/
|
|
|
Goto Forum:
Current Time: Wed Sep 25 13:43:10 GMT 2024
Powered by FUDForum. Page generated in 0.04198 seconds
|