Business Applications need to know when an attempt to send a command to device is feasible, e.g. because the device is then known to be connected to a protocol adapter. Devices and Protocol Adapters can indicate to Business Applications a device’s intent to receive commands using specific notifications.
Time until Disconnect Notification
Devices and Protocol Adapters can notify an application about the fact that a device is connected and ready to receive one or more commands by means of including a time till disconnect (ttd) property in telemetry or event messages.
The ttd property value indicates the amount of time (in seconds) that the device will stay connected to the protocol adapter. Using this value together with the creation-time of the message, an application can determine whether an attempt to send a command to the device has a reasonable chance of succeeding. The ttd property can be included in any regular telemetry or event message. However, if a device does not have any telemetry data or event to upload to the adapter, it can also use an empty notification instead.
Hono includes utility classes that application developers can use to register a callback to be notified when a device sends a ttd notification. See Hono’s example module for details where such a notification callback is used. Please refer to the Telemetry API and the Event API for further details.
The following table defines the possible values of the ttd property and their semantics:
|> 0||The value indicates the number of seconds that the device will stay connected. Devices using a stateless protocol like HTTP will be able to receive a single command only before disconnecting.|
|-1||The device is now connected (i.e. available to receive upstream messages) until further notice.|
|0||The device is now disconnected (i.e. not available anymore to receive upstream messages).|
Determining a Device’s Connection Status
An application receiving a downstream message containing a ttd property can check if the device is currently connected (and thus ready to receive a command) by
- adding the ttd value to the creation-time to determine the expiration time, and then
- comparing the current time with the expiration time
If the current time is after the expiration time, the device should be assumed to already have disconnected again.
Source of the ttd Value
While it seems to be natural that a device itself indicates when it is ready to receive a command, it may not always be possible or desirable to do so. A device could e.g. be not capable to specify the value for ttd in its message, or all devices of a particular setup would always use the same value for ttd, so it would not make much sense to provide this value with each request. Additionally, different protocols may not allow the sender to set specific values for a message, so a device using a specific protocol may not be able to provide a value for the ttd property at all. For these reasons there are additional ways of specifying the ttd:
- Hono’s Tenant and Device Registration APIs support the inclusion of default values for application-properties in the AMQP 1.0 message. This way, a device can be configured to always have a specific value for ttd set in messages originating from the device.
- In a future extension there may be a configuration value per tenant and protocol adapter that sets the value of ttd if it was not provided by other means already (like provided to the protocol adapter or by setting a default value).
CoAP protocol adapter
Hono’s CoAP protocol adapter supports the setting of the ttd value in requests explicitly. Please refer to the CoAP Adapter user guide for details. Alternatively, a default ttd property value can be specified for devices as mentioned above.
HTTP protocol adapter
Hono’s HTTP protocol adapter supports the setting of the ttd value in requests explicitly. Please refer to the HTTP Adapter user guide for details. Alternatively, a default ttd property value can be specified for devices as mentioned above.
The following sequence diagram shows a Time till disconnect notification while sending a telemetry message downstream via the HTTP protocol adapter:
The following sequence diagram shows a Time till disconnect notification by sending an empty event message downstream via the HTTP protocol adapter:
AMQP protocol adapter
The AMQP protocol adapter automatically initiates sending a Time till disconnect notification via the Command Router
with a ttd value of
-1 for a device that opens a receiver link for the command source address. Please refer to the
AMQP Adapter user guide for details.
When a device closes the receiver link again, the adapter automatically initiates a Time until disconnect notification
via the Command Router with a ttd value of
MQTT protocol adapter
The MQTT protocol adapter automatically initiates sending a Time till disconnect notification via the Command Router
with a ttd value of
-1 for a device that subscribes to the appropriate command topic. Please refer to the
MQTT Adapter user guide for details.
When a device unsubscribes again, the adapter automatically initiates a Time till disconnect notification via the
Command Router with a ttd value of