Eclipse Community Forums: Remote Application Platform (RAP) » Problem with RAP+BIRT target platform

Home » Eclipse Projects » Remote Application Platform (RAP) » Problem with RAP+BIRT target platform(Build errors after adding BIRT to the target platform)

Show: Today's Messages :: Show Polls :: Message Navigator

Problem with RAP+BIRT target platform [message #656171]

Thu, 24 February 2011 12:41

Paul Ramsden

Messages: 84
Registered: February 2011
Location: BW, Germany

Member

I am trying to add BIRT to my RAP application but am getting build errors once I add BIRT to the target platform configuration.

I have a RAP application using the standard RAP 1.3 Target from the Eclispe+RAP download and this builds and runs fine.

I downloaded the RAP 1.3 und the BIRT 2.6 runtimes and saved them to D:\TARGETS

I created a new target definition and added D:\TARGETS\RAP13. The project build is ok.

I edited the target definition and added D:\TARGETS\BIRT26. The build has many errors.

What I see is that the target definition editor deselects duplicate bundles automatically leaving just one bundle of a pair selected. It seems that the errors are caused by excactly these bundles not being found. I tried selecting the just the other bundle in each pair but I have the impression that the selection is automatically reverted when the config is saved.

Am I doing something wrong here? What can I do to narrow down the problem?

thanks!

Report message to a moderator

Re: Problem with RAP+BIRT target platform [message #656178 is a reply to message #656171]

Thu, 24 February 2011 13:00

Ivan Furnadjiev

Messages: 2426
Registered: July 2009
Location: Sofia, Bulgaria

Senior Member

Hi,
are you aware of this wiki page
http://wiki.eclipse.org/RAP/BIRT_Integration ?
This is a quotation from the "Target" chapter:
"When merging the two runtimes together, we should be sure that *no
bundle* is available *twice* as this results in same strange errors
during runtime. So first step is to remove all the duplicate bundles."
HTH,
Ivan

On 2/24/2011 2:41 PM, paulr wrote:
> I am trying to add BIRT to my RAP application but am getting build
> errors once I add BIRT to the target platform configuration.
>
> I have a RAP application using the standard RAP 1.3 Target from the
> Eclispe+RAP download and this builds and runs fine.
>
> I downloaded the RAP 1.3 und the BIRT 2.6 runtimes and saved them to
> D:\TARGETS
>
> I created a new target definition and added D:\TARGETS\RAP13. The
> project build is ok.
>
> I edited the target definition and added D:\TARGETS\BIRT26. The build
> has many errors.
>
> What I see is that the target definition editor deselects duplicate
> bundles automatically leaving just one bundle of a pair selected. It
> seems that the errors are caused by excactly these bundles not being
> found. I tried selecting the just the other bundle in each pair but I
> have the impression that the selection is automatically reverted when
> the config is saved.
>
> Am I doing something wrong here? What can I do to narrow down the
> problem?
>
> thanks!

Report message to a moderator

Re: Problem with RAP+BIRT target platform [message #656189 is a reply to message #656178]

Thu, 24 February 2011 13:41

Paul Ramsden

Messages: 84
Registered: February 2011
Location: BW, Germany

Member

Ivan,

yes, I was following that page.

As I mentioned in my question, the target editor seems to be deselecting the duplicates automatically so I don't think that I have any duplicates. However, the symptoms are that the duplicated bundles don't seem to be present *at all*.

Paul

Report message to a moderator

Re: Problem with RAP+BIRT target platform [message #656193 is a reply to message #656189]

Thu, 24 February 2011 14:05

Ivan Furnadjiev

Messages: 2426
Registered: July 2009
Location: Sofia, Bulgaria

Senior Member

Hi Paul,
try to compose you target platform manually without a duplicates bundles.
Best,
Ivan

On 2/24/2011 3:41 PM, paulr wrote:
> Ivan,
>
> yes, I was following that page.
> As I mentioned in my question, the target editor seems to be
> deselecting the duplicates automatically so I don't think that I have
> any duplicates. However, the symptoms are that the duplicated bundles
> don't seem to be present *at all*.
>
> Paul

Report message to a moderator

Re: Problem with RAP+BIRT target platform [message #657597 is a reply to message #656193]

Thu, 03 March 2011 12:37

Paul Ramsden

Messages: 84
Registered: February 2011
Location: BW, Germany

Member

Hi Ivan

ok, copied the RAP & BIRT manually as you suggested and it works fine.

NOTE the birt.api bundle needs to be deselected as it was causing a problem with com.ibm.icu.text.

Thanks

Paul

Report message to a moderator

Previous Topic:	[DateTime] Selection event lost
Next Topic:	Runtime issue on rendering images in table?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Tue Apr 16 15:09:56 GMT 2024

.:: Contact :: Home ::.

Breadcrumbs

Sign up to our Newsletter