Skip to main content


Eclipse Community Forums
Forum Search:

Search      Help    Register    Login    Home
Home » Modeling » EMF "Technology" (Ecore Tools, EMFatic, etc)  » Getting start with emf compare
Getting start with emf compare [message #135118] Sat, 18 April 2009 16:35 Go to next message
Thomas L is currently offline Thomas LFriend
Messages: 9
Registered: July 2009
Junior Member
Hello,

I want to use EMF Compare for a little project and I've got some problems
to start compare. The Wiki page
(http://wiki.eclipse.org/Installing_and_Using_EMF_Compare) can't
unfortunately help. I'm using the Eclipse Modeling Tools (includes
Incubating components) in the current version. Additional how can I
integrate Compare for use only the compare engine and get the diff model
(or delta model)?

Thank you for your help.

Thomas

Report message to a moderator

Re: Getting start with emf compare [message #135131 is a reply to message #135118] Sat, 18 April 2009 16:42 Go to previous message
Oleg Vazhnev is currently offline Oleg VazhnevFriend
Messages: 42
Registered: July 2009
Member
Hi Thomas

I was asking the same question a time ago :)
Let me copy-paste the answer.
Probably this will help.

Thanks,
Oleg

Hi Oleg,

Indeed that wiki page you're pointing to is only for developping patches
or applications needing EMF Compare sources. You need not retrieve any
of these in your workspace if you only intent on comparing models
without patching the comparison engines.

The unresolved dependencies you had when downloading the source code
points us to a possible answer as to why you cannot compare models
though. You have to have installed EMF prior to installing EMF Compare.

You can use the Ganymede update site for both of these : in your Eclipse
select help => Software Updates. In the newly opened dialog open the tab
"Available Software". In this tab should be a section "Ganymede"; expand
it (this could take quite some time) and expand the category "Models and
Model Development". In this category, select both "EMF" and "EMF Compare
(Incubation)" then click on "Install..." and you're all set.

You can then compare models following the information on
http://wiki.eclipse.org/Installing_and_Using_EMF_Compare .

Cheers,

Laurent Goubet


Thomas L wrote:
> Hello,
>
> I want to use EMF Compare for a little project and I've got some
> problems to start compare. The Wiki page
> (http://wiki.eclipse.org/Installing_and_Using_EMF_Compare) can't
> unfortunately help. I'm using the Eclipse Modeling Tools (includes
> Incubating components) in the current version. Additional how can I
> integrate Compare for use only the compare engine and get the diff model
> (or delta model)?
>
> Thank you for your help.
>
> Thomas
>

Report message to a moderator

Re: Getting start with emf compare [message #620830 is a reply to message #135118] Sat, 18 April 2009 16:42 Go to previous message
Oleg Vazhnev is currently offline Oleg VazhnevFriend
Messages: 42
Registered: July 2009
Member
Hi Thomas

I was asking the same question a time ago :)
Let me copy-paste the answer.
Probably this will help.

Thanks,
Oleg

Hi Oleg,

Indeed that wiki page you're pointing to is only for developping patches
or applications needing EMF Compare sources. You need not retrieve any
of these in your workspace if you only intent on comparing models
without patching the comparison engines.

The unresolved dependencies you had when downloading the source code
points us to a possible answer as to why you cannot compare models
though. You have to have installed EMF prior to installing EMF Compare.

You can use the Ganymede update site for both of these : in your Eclipse
select help => Software Updates. In the newly opened dialog open the tab
"Available Software". In this tab should be a section "Ganymede"; expand
it (this could take quite some time) and expand the category "Models and
Model Development". In this category, select both "EMF" and "EMF Compare
(Incubation)" then click on "Install..." and you're all set.

You can then compare models following the information on
http://wiki.eclipse.org/Installing_and_Using_EMF_Compare .

Cheers,

Laurent Goubet


Thomas L wrote:
> Hello,
>
> I want to use EMF Compare for a little project and I've got some
> problems to start compare. The Wiki page
> (http://wiki.eclipse.org/Installing_and_Using_EMF_Compare) can't
> unfortunately help. I'm using the Eclipse Modeling Tools (includes
> Incubating components) in the current version. Additional how can I
> integrate Compare for use only the compare engine and get the diff model
> (or delta model)?
>
> Thank you for your help.
>
> Thomas
>

Report message to a moderator

Previous Topic:Getting start with emf compare
Next Topic:Datatype Identifier problem
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Tue Apr 23 11:01:55 GMT 2024

Powered by FUDForum. Page generated in 0.02889 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.2.
Copyright ©2001-2010 FUDforum Bulletin Board Software

Back to the top

Sign up to our Newsletter

A fresh new issue delivered monthly