Eclipse Community Forums: Papyrus » how to enable code generation?

Home » Modeling » Papyrus » how to enable code generation?(If you have an existing Papyrus project, how do you enable C++ code generation?)

Show: Today's Messages :: Show Polls :: Message Navigator

how to enable code generation? [message #1749692]

Fri, 09 December 2016 17:53

Allen Curtis

Messages: 3
Registered: December 2016

Junior Member

Hello,

Is it possible to enable C++ code generation for an existing Papyrus project? I have been able to create a new project with this capability. However I can not figure out how to enable this feature after the fact.

Thanks

Report message to a moderator

Re: how to enable code generation? [message #1749755 is a reply to message #1749692]

Sun, 11 December 2016 09:33

Carsten Pitz

Messages: 495
Registered: May 2015
Location: Germany

Senior Member

Hi Allen,

Yes it is possible.

Beside the Papyrus Designer (https://wiki.eclipse.org/Papyrus_Software_Designer) other choices are
* Eclipse Obeo Acceleo (https://eclipse.org/acceleo/)
and
* Eclipse XPand (https://eclipse.org/modeling/m2t/?project=xpand).

Which of these three choices fits best, depends on your specific needs.

All three choices can be added to existing projects. But most likely the existing models have to be adapted to fit the requirements of the generator.

Best regards
Carsten

[Updated on: Sun, 11 December 2016 09:38]

Report message to a moderator

Re: how to enable code generation? [message #1749820 is a reply to message #1749755]

Mon, 12 December 2016 21:55

Allen Curtis

Messages: 3
Registered: December 2016

Junior Member

Hello,

I believe by default the code generator is Obeo Acceleo. How is this enabled for an existing project?

Thanks

Report message to a moderator

Re: how to enable code generation? [message #1749824 is a reply to message #1749820]

Mon, 12 December 2016 22:15

Allen Curtis

Messages: 3
Registered: December 2016

Junior Member

Hello again Carsten,

I went back to the Eclipse software configuration. This is what is reported for C++ code generation.

Papyrus C++ profile, view and code generation (Incubation) 1.0.3 org.eclipse.papyrus.designer.languages.cpp.feature.feature.group Eclipse Modeling Project
C/C++ Development Tools 9.1.0.201609121658 org.eclipse.cdt.feature.group Eclipse CDT
C/C++ Common GDB Support 9.1.0.201609121658 org.eclipse.cdt.gdb.feature.group Eclipse CDT
C/C++ Development Platform 9.1.0.201609121658 org.eclipse.cdt.platform.feature.group Eclipse CDT
C/C++ Development Tooling Native Utilities 9.1.0.201609121658 org.eclipse.cdt.native.feature.group Eclipse CDT
C/C++ DSF GDB Debugger Integration 9.1.0.201609121658 org.eclipse.cdt.gnu.dsf.feature.group Eclipse CDT
C/C++ GNU Toolchain Build Support 9.1.0.201609121658 org.eclipse.cdt.gnu.build.feature.group Eclipse CDT
C/C++ GNU Toolchain Debug Support 9.1.0.201609121658 org.eclipse.cdt.gnu.debug.feature.group Eclipse CDT
Papyrus base elements for code generation (Incubation) 1.0.3 org.eclipse.papyrus.designer.languages.common.feature.feature.group Eclipse Modeling

I don't see either of those packages installed.

Allen

Report message to a moderator

Re: how to enable code generation? [message #1749846 is a reply to message #1749824]

Tue, 13 December 2016 08:21

Carsten Pitz

Messages: 495
Registered: May 2015
Location: Germany

Senior Member

Hi Allen,

your list only contains CDT (C/C++ Development Tool) parts. Consequently I assume Eclipse Obeo Acceleo is not installed.

Best regards
Carsten

Report message to a moderator

Re: how to enable code generation? [message #1749870 is a reply to message #1749824]

Tue, 13 December 2016 12:46

Charles Rivet

Messages: 219
Registered: May 2014
Location: Canada

Senior Member

Hi Allen,

Did you install the Papyrus Designer-CPP Additional Component?

Doing so would bring in all the resources to be able too do code generation to C++.

To install Designer-CPP, you can do the following:

Click on the first "Papyrus Ibis" icon on the toolbar (the one without a drop-down menu) - this will bring up the "Additional Components Discovery" dialog.
Select the "Designer-CPP" extension.
Click [Finish]

After restarting Papyrus, you will have the Designer-CPP menu items.

/Charles Rivet

Report message to a moderator

Re: how to enable code generation? [message #1749890 is a reply to message #1749820]

Tue, 13 December 2016 14:29

Ansgar Radermacher

Messages: 470
Registered: March 2011
Location: Paris Saclay, France

Senior Member

Hi Allen,

if you install Papyrus SW designer (and in particular the C++ or Java code generation), the code generation will be technically based on xtend. Thus, there is no need to install Acceleo.

The C++ or Java code generators support structural code generation and behavior in form of opaque behavior declarations inside the model. There is a quite complete support for state-machine code generation based on a model-2-model transformation that is executed prior to code generation. A good starting point are the examples. (File->New Example).

Report message to a moderator

Previous Topic:	Hide Welcome page
Next Topic:	Beginner question - sequence diagram drag&drop

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Fri Sep 13 12:59:32 GMT 2024

.:: Contact :: Home ::.

Breadcrumbs

Sign up to our Newsletter