Eclipse Community Forums
Forum Search:

Search      Help    Register    Login    Home
Home » Modeling » Epsilon » [Eugenia] gmfgen model and "generate diagram code" option
[Eugenia] gmfgen model and "generate diagram code" option [message #651588] Mon, 31 January 2011 13:19 Go to next message
Aran A is currently offline Aran A
Messages: 21
Registered: January 2011
Junior Member
Hello,

I am newbie in GMF and Eugenia. I'm trying to follow the tutorial ( http://www.eclipse.org/gmt/epsilon/doc/articles/eugenia-gmf- tutorial/) complemented by the demo (http://www.eclipse.org/gmt/epsilon/cinema/Eugenia.htm), and I'm stacked.

I follow the steps of the tutorial and I get different models, OK, then I synchronize the .gmfgen model. Apparently everything is ok (I don't get any message), then I go to the next step "Right click the .gmfgen model again and select Generate diagram code", but I can't see the "Generate diagram code" option in the menu. I don't know what I'm doing wrong, any clue? Thanks in advance.

Best regards,

Arantza

Report message to a moderator

Re: [Eugenia] gmfgen model and "generate diagram code" option [message #651659 is a reply to message #651588] Tue, 01 February 2011 02:31 Go to previous messageGo to next message
Dimitris Kolovos is currently offline Dimitris Kolovos
Messages: 372
Registered: July 2009
Senior Member
Hi Aranza,

It seems that GMF has not been fully installed. Please click the "Install Modeling Components" button on the toolbar (or in the Help menu) and install it from the list that pops up. Please let me know if the problem persists.

Cheers,
Dimitris

Report message to a moderator

Re: [Eugenia] gmfgen model and "generate diagram code" option [message #651799 is a reply to message #651659] Tue, 01 February 2011 11:17 Go to previous messageGo to next message
Aran A is currently offline Aran A
Messages: 21
Registered: January 2011
Junior Member
That's it!!, Now it's working, thanks a lot.

Regards,

Arantza

Report message to a moderator

Re: [Eugenia] gmfgen model and "generate diagram code" option [message #657060 is a reply to message #651799] Tue, 01 March 2011 08:52 Go to previous messageGo to next message
Christoph Wienands is currently offline Christoph Wienands
Messages: 55
Registered: July 2009
Member
Wow, this is so weird. I see exactly the same issue. You would think that when you download the Helios MODELING edition it already comes with all modeling components.

Christoph

PS: By the way, the command can be found on the Help menu.

Report message to a moderator

Re: [Eugenia] gmfgen model and "generate diagram code" option [message #990438 is a reply to message #657060] Wed, 12 December 2012 08:56 Go to previous messageGo to next message
Joost van Pinxten is currently offline Joost van Pinxten
Messages: 39
Registered: November 2012
Member
That's odd behaviour indeed. I've also downloaded a clean version of Eclipse Modeling Tools and was able to build a GMF editor all the way up to the point where a gmfgen file is generated. I noticed that it didn't have the "Generate diagram code" and then realized I was working in a "Sample reflective EMF editor".

Report message to a moderator

Re: [Eugenia] gmfgen model and "generate diagram code" option [message #990449 is a reply to message #990438] Wed, 12 December 2012 09:36 Go to previous message
Dimitris Kolovos is currently offline Dimitris Kolovos
Messages: 372
Registered: July 2009
Senior Member
Hi Joost,

This happens because GMF Tooling is not pre-installed in the bundled modelling distributions. If memory serves, it was left out in an effort to slim down the modelling distribution as it was getting too bulky.

Cheers,
Dimitris

Report message to a moderator

Previous Topic:[EWL] Run an ETL transformation from EWL
Next Topic:[EMFatic] Reference problems in metamodel
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Mon May 20 02:59:55 EDT 2013

Powered by FUDForum. Page generated in 0.01776 seconds